Library power supplies Note: Drive 0 bus ID data field screen two-drive model shown 5. Host cable Bus 0, to host system Figure Damage may occur if inappropriate media is used in tape drives. This active mode can interfere with host-based application software, causing data loss.

Uploader: Arashigal
Date Added: 8 June 2016
File Size: 48.75 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 3317
Price: Free* [*Free Regsitration Required]

Configuration, Default Ethernet Settings HP recommends that you change these values from the defaults. Avoid touching pins, leads, or circuitry. Hewlett-Packard Company products are set forth in the express limited warranty statements accompanying such products.

SCSI option selection screen two-drive model shown Note: Sections in this chapter include the following: Use the longer Cycle power hp ultrium 5-scsi scsi sequential device the library or reboot using operation.


Page Table The remaining slots on the library do not support the connections that are required for the library controller board to operate correctly. Cleaning operation failed because the bp timed out. Install a cleaning cartridge in a reserved hp ultrium 5-scsi scsi sequential device. This manual also for: Table Of Contents Library Options This is a factory only diagnostic used to measure tachometer motor function limits.

Hp StorageWorks MSL5000 series User Manual

Run a Vertical Calibration test from the Diagnostics section of the Utilities menu. Select the Move Devicw option from the library Status screen.

The loader could not successfully stow an orphan cartridge to a bin. GUI touch screen that interrupts the current library operation off-line. Ensure that the library is idle before attempting to hp ultrium 5-scsi scsi sequential device any remote operations that will take the library offline.

Your software application may number these items beginning with 1. Click Execute the Move. More than one label applied, as extra labels can cause the cartridges to jam in the tape drive. Ensure sci the leader is in the correct position 1 in Figure hp ultrium 5-scsi scsi sequential device on page and Figure 76 on page Fixed Ip Address Screen 4.

Invalid user initiated operation. Reason the GUI touch screen.

Page GUI touch screen. One of the flash memory sectors could not be programmed. Handle and store tape cartridges in a clean, dust-free environment.

Operating system type and revision level Name and revision of application software HP Storage Website The HP website has the latest information on this product, as well as the latest drivers. Fixed IP address screen 6. A peg message hp ultrium 5-scsi scsi sequential device a pointer to NULL. The settings are Do Not Initiate hp ultrium 5-scsi scsi sequential device Initiate.

Devicee can move to the next subsequent Library Options screen by selecting the button. Base Address The default is 0x0. Page 84 Both Mail Slots Enabled. Attaching A Bar Code Label To An Ultrium Tape Cartridge To ensure successful operation of your tape library, place the bar code label entirely within the recessed area, ensuring that no part of the label is outside of it seeFigure Using Menu Buttons, Status drives and slots are grouped by library moduledepending on your preference.

Contact your authorized service provider. For optimal performance, do not attach more than two drives per SCSI bus. The default is Disabled. To reduce the risk of electrical shock, fire, devicf damage to the equipment, do not plug telephone or telecommunications connectors into this receptacle.

Touch the Save option to confirm your request. Check the SCSI cable connections to make sure they are secured. Setting Up The Tabletop Model, Tabletop Model Clearances two-drive Model Shown To reduce tabletop clearance requirements, temporarily move the library forward or rearward to access the hot-plug drive shoes and magazines, respectively.

The resulting information may be helpful to your service provider in resolving potential issues that may have prompted the firmware upgrade.

Bar hp ultrium 5-scsi scsi sequential device labels are displayed if enabled and in use.

Backing up several small files can impact performance. Page 43 Installation Note: Page In most cases, hardware compression should be enabled.

Possible settings are 1 through 8. Page Cycle power to the router. To print the manual completely, please, download it.